Video Bitrate Calculator

Find the bitrate that fits a size limit, the size a bitrate gives, or how long a video fits. Nothing is uploaded – there is no file here at all.

Duration

MB = 1,000,000 bytes, MiB = 1,048,576 bytes; GB and GiB the same, a thousand or 1,024 times larger.

Type 0 audio for a silent video. The reserve is the share of the file left for the container and for the encoder overshooting.

MB or MiB decides whether it fits

A megabyte is 1,000,000 bytes; a mebibyte is 1,048,576. Some systems show the second and still call it MB. When a limit is tight, aim at the smaller reading and check the exact byte count under the result.

Does the clip need its sound?

Set the audio to 0 and the picture gets the whole budget. Remove Audio from Video mutes an MP4, MOV or WebM without re-encoding the picture, in your browser.

Advertisement

How it works

One sum, solved three ways

A file is its bitrate times its length: bytes = bits per second × seconds ÷ 8. Ten minutes at 8 Mbps of video and 128 kbps of audio is 8,128,000 × 600 ÷ 8 = 609.6 MB of stream. Turn the same sum around and you get the bitrate that fits a size, or the length that fits at a bitrate. All three modes use it, so they agree with each other to the byte.

MB and MiB are not the same size

A megabyte (MB) is 1,000,000 bytes and a mebibyte (MiB) is 1,048,576, almost 5% more. A limit read the wrong way is the most common reason a carefully sized file is refused. The unit list says which is which, and the result always prints the exact byte count, so you can compare it with the limit as written.

The audio comes out of the budget first

To fit 10 MB in one minute the whole file can average about 1,293 kbps with the default reserve. A 128 kbps audio track takes its share, so the video gets about 1,165 kbps. The result lists video, audio and total separately. If the audio alone would fill the size, the page says there is no room for video rather than printing a zero.

An average to aim at, not a promise

Encoders spend more bits on busy scenes and fewer on still ones, so a bitrate figure is an average. A target-bitrate encode, best with two passes, lands close to it; a quality setting such as CRF does not aim at a size. The container adds a little too. That is what the reserve is for: 3% by default, printed with every answer, and yours to change.

YouTube’s upload figures, from YouTube

The YouTube list holds the SDR upload bitrates from YouTube Help, read on 1 November 2026: 8 Mbps for 1080p at 24 to 30 fps, 12 Mbps at 48 to 60 fps, 35 to 45 Mbps for 4K. YouTube calls them recommendations, not caps. For a 4K range the page fills in the low end. They are a starting point for an upload, not a quality grade.

The formula worked three ways, MB versus MiB, and why CRF misses a size: how to calculate video bitrate and file size.

Frequently Asked Questions

How do I calculate video bitrate from file size?

Multiply the size in bytes by 8 to get bits, then divide by the length in seconds. That is the total bitrate; take the audio bitrate away to get what the video can use. For 10 MB over one minute: 10,000,000 × 8 ÷ 60 = 1,333 kbps in total, or about 1,293 kbps after a 3% reserve, which leaves about 1,165 kbps for video next to 128 kbps of audio.

How do I calculate video file size from bitrate?

Add the video and audio bitrates, multiply by the length in seconds and divide by 8. Ten minutes at 8 Mbps video and 128 kbps audio is 609.6 MB of stream, and about 628 MB once a 3% reserve for the container is added. The page shows the decimal and binary sizes and the exact byte count.

Why did my file come out bigger than the calculator said?

Usually one of three things. The encoder ran in a quality mode such as CRF, which does not aim at a size. The limit was in MiB and the encode was aimed at MB, or the other way round. Or the reserve was too small for that container and encoder. Use a target bitrate with two passes and raise the reserve a little if a limit is strict.

Is 1 MB 1,000 KB or 1,024 KB?

Both are in use, which is the problem. Strictly, MB is 1,000,000 bytes and MiB is 1,048,576 bytes, but some software shows MiB and labels it MB. Pick the unit your limit is written in; if you cannot tell, use MB: it is the smaller unit, so a file sized to it fits the limit whichever way it was meant.

Does the audio bitrate matter?

Yes. In a small file it can be a large share: 128 kbps of audio over ten minutes is 9.6 MB on its own, so a 10 MB target leaves almost nothing for the picture. The page subtracts the audio first and says when there is no room left. A clip that does not need sound can have its audio removed and give the video the whole budget.

What bitrate does YouTube recommend?

For SDR uploads YouTube Help lists 8 Mbps for 1080p at 24 to 30 fps, 12 Mbps at 48 to 60 fps, 5 and 7.5 Mbps for 720p, 16 and 24 Mbps for 1440p, and 35 to 45 or 53 to 68 Mbps for 4K. YouTube says no bitrate limit is required. The figures were read on 1 November 2026 and are in the list on this page.

Does a higher bitrate mean better quality?

Only for the same codec, resolution and footage. HEVC or AV1 can look as good as H.264 at a lower bitrate, and a static talking head needs far less than fast sport. That is why this page gives no quality grade: a bitrate says how big the file is, not how good it looks.

What is the reserve for?

The bitrate counts only the audio and video data. The container adds headers and an index, and an encoder can overshoot its target a little. The reserve is the share of the file kept back for both: 3% by default. The page uses the same reserve whichever way you solve, so the file size for a bitrate and the bitrate for that size match exactly.

Is anything uploaded or stored?

Nothing. There is no file, no server call and no account. The sum runs in JavaScript on your own device, and the numbers you type are not sent anywhere or kept once you close the tab.